Home / News

To find where to buy capsule filling machine, first thing first you should get to know capsule filling machine. The automatic capsule filler integrates machine, electricity and gas, adopts microcomputer programmable controller, touch panel operation, frequency conversion speed regulation, and is equipped with an electronic automatic counting device, which can automatically complete the positioning, separation, filling, and locking of the capsule. , Reduce labor intensity, improve production efficiency, and meet the requirements of pharmaceutical hygiene. The machine is sensitive in action, accurate in filling dosage and easy to operate. It is suitable for filling various domestic or imported capsules. It is an economical and practical equipment for filling capsule drugs in the pharmaceutical industry.

The working principle of capsule filling machine

Generally, it adopts automatic intermittent rotary motion form. It is installed on the rotary table in the center of the worktable. There are 8 short stays for each revolution. The rotary table transports the capsules to the various workstations around the rotary table. , Divide, fill, remove waste, lock, discharge, clean molds and other operations automatically at the same time.

buy capsule filling machine

The Steps of capsule filling machine

1. Press the green button in the "Power Switch" to turn on the power.

2. Slowly adjust the "Vibration Strength Adjustment Knob" and turn it clockwise. At this time, the sorting tray integrated with the "vibration bracket" starts to vibrate, touch the sorting tray with your hand, and adjust to a certain vibration intensity by feeling.

3. Put the powder-filled capsule shells into the "powder-filled capsule shell sorting tray", about 300 capsules each time. Put the capsule cap into the "capsule cap sorting tray", about 300 capsules each time. The sorting tray is made of plexiglass plate, and there are many round holes in the shape of a funnel, the diameter of which corresponds to the diameter of the capsule number. At this time, the capsule shell of the vibrating worktable moves steadily back and forth, so that the pellets enter the plate hole one by one.

4. About 30 seconds, the powder-filled capsule shell and capsule cap will drop into the round hole with the opening facing upward. In case of individual openings facing downwards, the caps of the capsules can be gently pressed down to pull out.

5. Hold the powder capsule shell connecting plate horizontally (shown at the end of the picture, it has been prepared at random, and there are round holes in the connecting plate).

Gently push the lower part of the tray inward, and the powder capsule shell in the sorting tray will drop down into the round hole of the connecting plate, and then take out the connecting plate. In the same way, remove the capsule cap with the capsule cap connecting plate.

6. You can prepare a medicinal powder square plate with a bottom area of 500×500mm and a height of about 10mm on four sides in advance, containing the powdered medicine, and place the powder-filled capsule shell connecting plate in the powdered square plate. Then put the randomly equipped plexiglass frame on the powder capsule receiving plate, put the powder into the frame with a small bucket, and scrape the edge of the frame to fill the powder and scrape off the excess powder.

7. Use the randomly equipped capsule cap cover plate (shown at the end of the picture, the cover plate has a round hole), put it on the capsule cap cover plate, there are alignment holes, it is easy to place. Turn over the cap connecting plate of the capsule so that the opening of the capsule faces downwards, and put it on the powder-filled capsule connecting plate that has been filled with powder. There are also alignment holes for easy fitting.

8. Put the nested capsule board into the cavity under the "capsule cap forming board", pull the "pressing rod" down by hand and place it in place. There is no need to be careful of excessive force, because the positioning mechanism controls the pressing down height. Take out the sleeved capsule plate, pour out the capsule, and finish filling. You can cycle to the next board.

malfunction capsule filling machine

Precautions of automatic capsule filling machine

1. This equipment is a vibrating machine. The tightening of the screws in each part should be checked frequently. If there is looseness, it should be tightened in time to prevent malfunction and damage.

2. The plexiglass components (worktable, medicine board) should be protected from direct sunlight and close to high temperature, and heavy objects must not be placed. The medicine board must be placed vertically or flat to avoid deformation and damage.

3. The electrical shell and body must be grounded to ensure safety. Cut off the power supply after work. 

4. After working every day, you should clean up the residual medicine on the machine and the mold hole, keep the whole machine clean and hygienic, and avoid washing the main machine with water. If the mold on the machine needs to be cleaned, the fixing screws can be loosened and then removed, which is convenient for installation.

The malfunction repair of capsule filling machine

1. The vibration is not ideal, adjust the voltage.

2. The reed screw is loose, tighten the screw.

3. The capsule shells are arranged in the worktable, the mouth is higher or lower, adjust the height of the misaligned plate and the guide rail.

4. Too many capsule shells are turned upside down (more than 3%), the vibrator is improperly adjusted, because the proper voltage is adjusted or the size of the capsule shell is out of specification, select a qualified capsule shell.

5. The capsule shell is stuck on the platen and cannot fall. Replace the capsule shell or adjust the position of the dislocation plate and the plate hole.

6. The mold cannot be reset in the rail, the compression spring at the rear end of the rail is stuck or the capsule is deformed. Reinstall the spring or ejector rod, and push down the stuck capsule with the push rod.

7. The guide plate in the mold is worn, which affects the low rate of capsule fit. Replace with a new mold or loose positioning on both sides, tighten the positioning nails, and the capsule is deformed or wet. Replace the capsule shell.

We also manufacture automatic tube filling and sealing machinestrip pack machinehigh shear mixer granulator and some other pharmaceutical machineries for buyers, welcome to contact us!